Graflex.org Forum Index Graflex.org
Get help with your Graflex questions here
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Burke & James Press 4x5: restoration... need help, plz!

 
Post new topic   Reply to topic    Graflex.org Forum Index -> Non-Graflex Cameras
View previous topic :: View next topic  
Author Message
LF4Fun



Joined: 28 Aug 2010
Posts: 8

PostPosted: Tue May 15, 2012 4:28 pm    Post subject: Burke & James Press 4x5: restoration... need help, plz! Reply with quote

hi all,

I'm looking for guidance on how to:
1) soften the bellow. My B&J bellow is very stiff, I'm not sure if I can use Lexol Leather Conditioner on the bellow.
2) Revolving Back: can I disassemble and clean/relube it.

Thank you in advance. Any help is appreciated.
Back to top
View user's profile Send private message
1banjo



Joined: 16 Nov 2008
Posts: 492
Location: kansas

PostPosted: Tue May 15, 2012 5:49 pm    Post subject: Reply with quote

hey if you can find Pledge Natural Beauty works
Back to top
View user's profile Send private message
45PSS



Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.

PostPosted: Tue May 15, 2012 6:48 pm    Post subject: Reply with quote

Lexol may leave a sticky residue.
Neatsfoot oil, available at Tandy leather.
And as Banjo said Pledge Natural Beauty (yellow can).
_________________
The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
Back to top
View user's profile Send private message Visit poster's website
Henry



Joined: 09 May 2001
Posts: 1636
Location: Allentown, Pennsylvania

PostPosted: Tue May 15, 2012 8:44 pm    Post subject: Reply with quote

There was a time when Lemon Pledge was available in a non-aerosol plastic bottle with manual spritzer. I still have such a bottle from years gone by, and I even have occasion to use it from time to time. It made an excellent slide lubricant for my trombone, although its effectiveness didn't last very long before it gummed up. I've used it on the red bellows of my Century, with good results.
Back to top
View user's profile Send private message
LF4Fun



Joined: 28 Aug 2010
Posts: 8

PostPosted: Tue May 15, 2012 10:47 pm    Post subject: Reply with quote

thank you all. I'll give that Pledge a try.
any tip on how to clean & relube the revolving back?
Back to top
View user's profile Send private message
45PSS



Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.

PostPosted: Tue May 15, 2012 11:12 pm    Post subject: Reply with quote

I don't have a clue how B&J did their back.
If the back is removable from the camera remove it.
On the inside there may be screws that you remove to separate the the back sections. Remove those screws and carefully separate the back sections.
Clean the sections with alcohol, lube with a just detectable layer of white lithium grease and reassemble.
Use a digital camera to take pictures as you disassemble.

If the back uses nylon guides as the Super Graphics backs do then solvents and oils can damage the parts.

3in1 oil and WD 40 dry out quickly and leave a sticky residue.
TriFlow, watch oil or gun oil work well on cameras.
_________________
The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
Back to top
View user's profile Send private message Visit poster's website
1banjo



Joined: 16 Nov 2008
Posts: 492
Location: kansas

PostPosted: Wed May 16, 2012 4:46 am    Post subject: Reply with quote

you have to unglue the Bellows then 4 screws hold it in place
mine the bellows the glue was giving up so it was not hard to do
Back to top
View user's profile Send private message
45PSS



Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.

PostPosted: Wed May 16, 2012 6:35 am    Post subject: Reply with quote

Mosenblockers Lift Off Adhesive remover works well and is safe on finishes.
http://www.lowes.com/pd_16685-11743-407-45_0__?productId=3015285&Ntt=lift+off&pl=1&currentURL=%2Fpl__0__s%3FNtt%3Dlift%2Boff&facetInfo=
Goof Off must be used in a well ventilated area, might damage the bellows; Goo Gone leaves a oily residue that is hard to remove.

Try putting a 2 to 3 drops of oil in at the rotation release and rotate several times in both directions. Rotate 180° and oil as before and rotate some more.
_________________
The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
Back to top
View user's profile Send private message Visit poster's website
LF4Fun



Joined: 28 Aug 2010
Posts: 8

PostPosted: Wed May 16, 2012 9:31 pm    Post subject: Reply with quote

thank you all.
Looking from the front of the camera, I can see 3 screws, the 4th one might be obscured by the bellow. Will give it a try tonight.

thanks again.
Back to top
View user's profile Send private message
LF4Fun



Joined: 28 Aug 2010
Posts: 8

PostPosted: Fri May 18, 2012 7:14 am    Post subject: Reply with quote

okay... the revolving back is now clean & lube BUT the bellow is beyond repair. Does anyone know where I can get a replacement?

thank you for all your help.
Back to top
View user's profile Send private message
45PSS



Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.

PostPosted: Fri May 18, 2012 7:38 am    Post subject: Reply with quote

Were the bellows bad before you repaired the back or after?

Go to http://www.playerpianocompany.com/onlinecat.html
and get some #50 pneumatic cloth

http://www.playerpianocompany.com/catalog/leather-tubingconn.pdf
(now nylon, 45 inches wide) .008 thick.

Next get some DAP Nonflammable Contact Cement
http://www.lowes.com/pd_41159-68-25332_0__?productId=3033214&Ntt=contact+cement&pl=1&currentURL=%2Fpl__0__s%3FNtt%3Dcontact%2Bcement&facetInfo=

With the bellows removed from the camera extend and clamp them to a flat work surface. Measure the bellows and cut the pneumatic cloth to fit the inside of the bellows allowing for 1/2 to 1 inch overlap. Fold the cloth so that the rubber coating is the outer surface. Off setting the original seam coat one side of the inside of the bellows with the contact cement and while wet place the pneumatic cloth on the inside and press into place. Continue working around the bellows applying glue and unrolling the pneumatic cloth and pressing into place eliminating air pockets and wrinkles until the entire bellows is covered. Allow to dry. Dry glue not between the material will rub off. Starting at the rear refold the bellows according to the original folds. Reinstall into the camera. This works on torn and riped bellows.

1 inch foam brushes work well to spread the glue.
_________________
The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
Back to top
View user's profile Send private message Visit poster's website
LF4Fun



Joined: 28 Aug 2010
Posts: 8

PostPosted: Fri May 18, 2012 4:04 pm    Post subject: Reply with quote

Thanks a lot 45PSS.

would this increase the thickness of the bellow and make it hard to fold back into the camera? OR maybe I did not understand your instruction fully, especially this line "Off setting the original seam coat one side of the inside of the bellows with the contact cement and while wet place the pneumatic cloth on the inside and press into place."
Back to top
View user's profile Send private message
45PSS



Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.

PostPosted: Fri May 18, 2012 4:10 pm    Post subject: Reply with quote

It makes them thicker when folded but on a 26 inch bellows it only gained 1/4 inch or so fully compressed. Installing a second lining making its seam on top of the existing one will add extra unwanted thickness.

When cutting center the front perimeter measurement on the rear perimeter measurement and the sides will have the correct taper of the bellows.

The Anniversary Speed I'm repairing has 26 pleats in its bellows. .008*26=.208=.023 less than 13/64
_________________
The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Graflex.org Forum Index -> Non-Graflex Cameras All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group