Graflex.org Forum Index Graflex.org
Get help with your Graflex questions here
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Graflex 22 roll holder-switch out insert?

 
Post new topic   Reply to topic    Graflex.org Forum Index -> Film Help
View previous topic :: View next topic  
Author Message
Negative Energy



Joined: 14 Sep 2005
Posts: 17
Location: Philadelphia

PostPosted: Mon May 14, 2012 9:18 pm    Post subject: Graflex 22 roll holder-switch out insert? Reply with quote

I have a 3x4 Super D and it came with a 6x9 rollfilm back that appears functional, but I remember reading that there were film flatness problems. Can I switch out the mechanism such as those on the RH holders to obviate this? Are there other fixes?
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Dan Fromm



Joined: 14 May 2001
Posts: 2118
Location: New Jersey

PostPosted: Mon May 14, 2012 9:47 pm    Post subject: Re: Graflex 22 roll holder-switch out insert? Reply with quote

Negative Energy wrote:
I have a 3x4 Super D and it came with a 6x9 rollfilm back that appears functional, but I remember reading that there were film flatness problems. Can I switch out the mechanism such as those on the RH holders to obviate this? Are there other fixes?


If it is a 22, its shell will have a gate for nominal 6x6 and the film carriage that gives 12 shots per roll. Did you mean "23?"

Graflex' solution to the alleged film flatness problem was to put pin rollers ad the ends of the gate, that is, in the shell. Swapping the insert won't do this but inserts will swap between shells.

www.skgrimes.com will, for a fee, put pin rollers in a shell. Graflex didn't make roll holder shells with pin rollers to fit Graflex SLRs, so grimes' service may be your best bet. I don't know how much they charge.

FWIW, I have a 2x3 RB Ser B that I've used a little. Its 2x3 roll holder doesn't seem to have film flatness problems. Try yours out before doing anything.
Back to top
View user's profile Send private message
45PSS



Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.

PostPosted: Mon May 14, 2012 10:04 pm    Post subject: Reply with quote

http://graflex.org/helpboard/viewtopic.php?p=34231#34231

Film thickness has changed over the years. A RH series RFH has pin rollers in the shell to aid in keeping film flat.
EDIT:
Disregard the following modification, it may damage your insert.

Open you RFH and remove the insert. There are two bars across the top and two bars across the bottom of the film opening. Replace the insert, remove the darkslide and look at the pressure plate through the film opening. Note that the top and bottom outer bars touch the pressure plate while the inner ones do not. Cut a piece of black card stock (110lb) or poster board that is .010 inch thick. Target has it http://www.target.com/p/BLK-PSTR-BRD-22X28-IN-POSTER-BOARD/-/A-14045951
Cut a piece to fit between the two outer rails and the length of the pressure plate and glue it to the pressure plate with contact cement or similar flexible glue.
_________________
The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU.
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Graflex.org Forum Index -> Film Help All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group