View previous topic :: View next topic |
Author |
Message |
BillC
Joined: 29 Oct 2010 Posts: 1 Location: Allentown PA
|
Posted: Tue Nov 02, 2010 6:09 pm Post subject: Singer Graflex Ibsta-Load 16 Questions, Parts etc. |
|
|
New to forum, new to 16mm and matter of fact don't even own a 16mm film yet.
Singer Graflex 16mm Insta-Load
1) When in Forward/Load/Run should the front supply reel be turning under power or should it be free spinning?
2) When in Forward, without a film loaded, the take up reel mechanism appears to be slipping a lot where the arm drive mechsnism joins with the motor drive mechanism. Appears to be some form of slip clutch. If I hold onto the belt for the front arm its very hard to stop but the rear belt can be stopped with very little pressure. My first thought was some mechanism which tightened everything when a film was sensed but I couldn't find anything like that.
3) Where, if anywhere, can one get parts for these rigs or is this a candidate for the landfill?
Thanks |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
C. Henry
Joined: 13 Dec 2005 Posts: 360 Location: North East Georgia, USA
|
Posted: Tue Nov 02, 2010 8:13 pm Post subject: |
|
|
Bill;
Take a look at the thread below your post in this Forum. You may find some help there and certainly will find a name or two to ask.
C. Henry |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Tue Nov 02, 2010 8:40 pm Post subject: |
|
|
Based on memory of 35mm theater projection
Supply reel should turn freely, correction it should have a slight drag allowing drive mechanism to pull film easily into the projection head without the supply spilling off the reel. Take up reel should just take up the slack in the film as it exits the projection head/drive train without pulling on the film even when the reel is full.
If not repairable and not good for parts a metal recycler would be a better choice than the land fill.
I think the post CH was referring to is this one
http://www.graflex.org/helpboard/viewtopic.php?t=5579
posts can become separated at any time. _________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
dberman51
Joined: 12 Nov 2009 Posts: 5 Location: Massachusetts
|
Posted: Wed Nov 03, 2010 11:59 pm Post subject: |
|
|
In FORWARD mode: Feed reel will not rotate under power but should be able to be turned easily with light drag. Take-up reel has a slip clutch which is sensitive to the weight of the reel and the film on it. With no reel it will be very easy to stop the rotation. With a full 2300 ft reel it should be much harder to stop. Most projectors have some kind of weight-sensing mechanism for the take-up reel but I think the Graflex design is the best.
There are parts available. ICE/Magna-Tech ( http://www.iceco.com/ ) which supplies parts for B&H projectors has just picked up parts for Graflex. There are other sources as well. Are you sure you need parts? What isn't working? Maybe just a cleaning and lubrication is needed? What model machine are we talking about, something in the 1100 series?
This site has a lot of information about 16mm films and projectors:
http://www.16mmfilmtalk.com/
-David |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|