View previous topic :: View next topic |
Author |
Message |
shutter up
Joined: 03 Aug 2002 Posts: 10 Location: S.W. Central Iowa
|
Posted: Mon Sep 16, 2002 4:59 pm Post subject: |
|
|
Can anyone provide me with their own experiences or tips on measuring out developers/fixers/..etc for small amounts.
Rather than mixing the gallon worth and storing solutions? I'm only processing a couple of 4X5's @ a time and only use about 200 to 300ml of water. Is a tablespoon worth of agent too much? Not enough?
Any tips or suggestions would be greatly appreciated!!!!
Rob |
|
Back to top |
|
|
Henry
Joined: 09 May 2001 Posts: 1636 Location: Allentown, Pennsylvania
|
Posted: Mon Sep 16, 2002 8:22 pm Post subject: |
|
|
Kodak discourages the practice of mixing small quantities as you are suggesting. I've found a good way to preserve developer in solution. First, use a glass jug (if you can still find them anywhere in today's plastic world)---I don't trust plastic because of permeability issues. Next, and this is the crucial step, every time you remove your 200 or 300ml from the jug, take a soda straw and exhale through it into the jug about 5-10 times. This will put a layer of carbon dioxide in contact with the liquid surface and retard or prevent oxidation of the developer. I've kept D76 alive for several months using this technique, which was widely printed years ago in the photo mags. |
|
Back to top |
|
|
KeithNP
Joined: 30 Nov 2001 Posts: 26 Location: Loma Linda, CA
|
Posted: Mon Sep 16, 2002 9:50 pm Post subject: |
|
|
I think you could get better results with another technique. The problem is that exhaled air still has a fair amount of oxygen in it (thats why mouth-to-mouth works...). One technique would be to get a can of nitrogen (they sell them at some of the more classy wine shops to - you guessed it - stop an opened bottle of wine from oxidizing). The other technique is a little trickier, but works really well. Put the chemical in a bottle with a large (several inches) airgap. Put a deflated balloon in the neck of the bottle and then blow it up. As it fills, it will displace the air in the bottle, forming a tight seal.
You can also get little cylinders of CO2 for making soda water, or inflating bicycle tires, or blowing the dust off your keyboard, but I worry that the CO2 will dissolve into the solution (as carbonic acid) and lower the pH. Depending on the chemical, that might have an effect on its properties. With small amounts of chemicals, that pH change would be more rapid (less buffering effect).
As for the original question about how much solution to use, look online for some small graduated cylinders or pipettes. They will allow you to measure small amounts accurately. Then all you have to do is divide the original concentrations down to get the smaller amount. (10cc in 850ml = 1cc in 85ml etc.) |
|
Back to top |
|
|
Les
Joined: 09 May 2001 Posts: 2682 Location: Detroit, MI
|
Posted: Mon Sep 16, 2002 10:53 pm Post subject: |
|
|
When my B&W business was going great guns, I would buy ektaflo developer (but this would work with D76) and put the concentrate in indiviual bottles. I was able to by the brown glass pharmacy bottles---the ones with the funny 3 followed by roman numberals-- through my local pharmacy. a place called American Science and Surplus may have them cheaper.
this way I had a 'one shot' amount for my 8x10 trays. It worked well.
Now a word of caution about D76. As it ages, the pH changes and that effects the contrast. My "film Developer's Cookbook" isn't at hand at the moment, but Grant Hutchings suggests leaving out the Metol. The new formula is called D76H and can be purchased through Photographer's Formulary.
Another option is to change to Rodinal. this can be used as a one shot developer, the dilution is great, and therefore economical and Rodinal in concentrate lasts a long time too. |
|
Back to top |
|
|
LelandRay
Joined: 24 May 2001 Posts: 115 Location: Mississippi
|
Posted: Thu Sep 19, 2002 12:30 pm Post subject: |
|
|
I'm about to commit sacrilege...
When my B&W processing slows down a lot, I use Kodak TMAX concentrate. I just mix it 1:4 with water, as recommended. The concentrate doesn't last forever, but it's better than having a whole gallon of D76 go stale. |
|
Back to top |
|
|
Les
Joined: 09 May 2001 Posts: 2682 Location: Detroit, MI
|
Posted: Thu Sep 19, 2002 1:20 pm Post subject: |
|
|
Dear Leland Ray.
I've used Tmax dev with great results for their roll film, but I tried it with sheet film and got a tremendous amount of dichroic fog. How did you keep from getting it.?
Now that they are reformulating Tmax films, I don't know if that will continue.
_________________ "In order to invent, you need a good imagination and a lot of junk" Thomas Edison |
|
Back to top |
|
|
shutter up
Joined: 03 Aug 2002 Posts: 10 Location: S.W. Central Iowa
|
Posted: Thu Sep 19, 2002 1:45 pm Post subject: |
|
|
Thank you for all the replies!! This is the feedback I was looking for and will help greatly!!!!!!!! |
|
Back to top |
|
|
LelandRay
Joined: 24 May 2001 Posts: 115 Location: Mississippi
|
Posted: Fri Sep 20, 2002 8:07 pm Post subject: |
|
|
Ooooops, Les.
I actually haven't tried TMax developer with sheet film; since a single run is going to take half a gallon of chemistry anyway, I don't worry much about waste. Two runs to the gallon, so the developer doesn't have time to go stale. I was assuming (you know what they say about assumptions) that the results would be the same for sheet film as for roll film, which is 90% of my shooting / processing.
Guess I better start reading and writing a bit more carefully.
Leland |
|
Back to top |
|
|
Les
Joined: 09 May 2001 Posts: 2682 Location: Detroit, MI
|
Posted: Fri Sep 20, 2002 10:09 pm Post subject: |
|
|
Nooo Problem.
I can remember when this first came out they said that with a 120 single roll tank, you could do two runs at the normal time then add a minute and do two more runs.
Four rolls out of 16 oz of developer!
_________________ "In order to invent, you need a good imagination and a lot of junk" Thomas Edison |
|
Back to top |
|
|
clnfrd
Joined: 26 Mar 2002 Posts: 616 Location: Western Kentucky Lakes Area
|
Posted: Sat Sep 21, 2002 12:51 am Post subject: |
|
|
For what its worth...I remember when I was a kid visiting a local photog's darkroom. He mixed his developer in large brown jugs...placed a syphon hose with a clip on the end into each one...and poured an oil of some sort, probably mineral oil, onto the liquid surface. The oil stayed on top, of course, and kept the solution insulated from oxidation. He could add replenisher, and was careful never to let the level get low enough to syphon out the oil. Fred.
[ This Message was edited by: clnfrd on 2002-09-20 17:53 ] |
|
Back to top |
|
|
alecj
Joined: 09 May 2001 Posts: 853 Location: Alabama
|
Posted: Sat Sep 21, 2002 1:52 am Post subject: |
|
|
I use HC-110 and find it easy to measure out small amts for processing a few sheets. I don't like holding dev. over - I use mine one-time. Its still cheap enough, used that way, to justify the effort. Cheaper than other devs too. |
|
Back to top |
|
|
Lensman
Joined: 20 Jan 2002 Posts: 63 Location: British Columbia
|
Posted: Mon Sep 23, 2002 5:11 pm Post subject: |
|
|
Using DEKTOL as a fast developer for film. I used this at a newspaper when speed was essential in developing and printing.
Try undiluted/straight Dektol at 70 degrees F. for ONE MIN in a tray. Constant agitation by moving tray slightly.
OR- Dektol 1-1 at 3Min.@ 68deg. F.
Results were pretty good.
Discard after use.
I can't recall for sure, but I imagine one could use the same developer for a print from the 'wet' negative.
|
|
Back to top |
|
|
Les
Joined: 09 May 2001 Posts: 2682 Location: Detroit, MI
|
Posted: Mon Sep 23, 2002 6:49 pm Post subject: |
|
|
I just hope you like lots of grain! Back when it was fashionable, we used to shoot recording film (asa 1000) one stop under and then develop in Dektol 1:3 for 5 min I think. Had an interesting look, which is not the same as D-76!
Now we just lay the "19th Century Auto chrome" plug-in filter over the image and FTP it to the magazine.
_________________ "In order to invent, you need a good imagination and a lot of junk" Thomas Edison |
|
Back to top |
|
|
Nick
Joined: 16 Oct 2002 Posts: 494
|
Posted: Wed Oct 16, 2002 11:50 am Post subject: |
|
|
This is exactly one reason some people make up developer from basic chemicals. You make what you need when you need. It's a little more effort but not alot more. Well IMHO not a lot more. |
|
Back to top |
|
|
jpmose
Joined: 29 May 2001 Posts: 164 Location: Atlanta, GA
|
Posted: Thu Oct 17, 2002 8:53 pm Post subject: |
|
|
Another problem with your suggested use of "spooning" out the powder for individual uses are the weight variances of different ingredients. This can cause one or more ingredients to settle, resulting in an uneven mixture. I remember trying this back in my early days of darkroom practice (when I was a young lad in 1972) and getting very strange results.
_________________ Best regards,
JP Mose |
|
Back to top |
|
|
|