View previous topic :: View next topic |
Author |
Message |
DennisT
Joined: 17 Jul 2011 Posts: 8 Location: E WA state
|
Posted: Wed Jul 20, 2011 1:31 am Post subject: Graphex shutter stiff/stuck ring: partial disassembly? |
|
|
One of the three estate sale Graphics that I got this past weekend has a Graphex shutter that is pretty stiff. Acts to me like it is dry and needs cleaning, etc.
With 45PSS's tips, I've downloaded the Graflex shutter service manual. I see it has a nice write-up about taking them apart in stages. So if I do, for example, stage one, which effectively removes the first covering ring, I should be able to see most or all of the internals without taking tiny pieces out. Then is it possible to very carefully clean and put tiny, tiny amounts of lube in it without further disassembly?????
I hear lighter fluid is good for cleaning.
I have some very thin watch oil which is not supposed to thicken or dry out, (if that is possible over the long term).
Just trying to do my homework here. Doing fine work is not new to me.
Dennis _________________ Dennis |
|
Back to top |
|
|
Henry
Joined: 09 May 2001 Posts: 1639 Location: Allentown, Pennsylvania
|
Posted: Wed Jul 20, 2011 2:10 am Post subject: |
|
|
The first thing I would try is the "Ronsonol soak." Remove front and rear lens elements (unscrew CCW) and squirt the Ronsonol lighter fluid (naptha) into the front works, around the perimeter of the hole where the front lens was, while exercising (i.e., cocking and releasing) the shutter through all its speeds. You can also squirt the fluid into the slit where the shutter release lever resides, and into the synchronizer housing (if so equipped). In my experience, if the soak doesn't improve matters, then the shutter probably needs servicing; further disassembly (stage 1) probably would be futile, unless you yourself are prepared to work on it. If it needs parts (springs, etc.) you'd be better off sending it out, and there are several recommendations, as well as some cautions, that we can come up with for you. I myself would not use any lubricant on the shutter mechanism. Be sure to let the fluid evaporate *completely* (overnight) before reinstalling the lens elements. With luck this may be all it needs.
Last edited by Henry on Thu Jul 21, 2011 1:13 am; edited 1 time in total |
|
Back to top |
|
|
DennisT
Joined: 17 Jul 2011 Posts: 8 Location: E WA state
|
Posted: Wed Jul 20, 2011 3:24 am Post subject: Bingo |
|
|
Henry: Thank you for the tip. Actually, I had seen your similar comment when I did, "search," for such things earlier today. I immediately went downstairs and tried Ronsonol. I was able to find my $0.79 can right away; no idea why I had it in the first place.
Worked. After removing the front lens, it was easy to see a lot of stuff inside the shutter already, which I liked. Everything works now except when I turn the outer ring beyond 200 speed toward 400 speed, the ring stops. I also notice the ring movement is not entirely smooth. I suppose, in field camera work, that ring could eventually pick up a bit of fine dust. That's what it feels like. Over all, everything inside the shutter looks really clean....to the eye anyway.
But tonight it was working with residual fluid on the parts. Tomorrow I'll get the real story.........
Still confused about no 400 speed though........
Dennis _________________ Dennis |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Wed Jul 20, 2011 5:40 am Post subject: |
|
|
If you found the manual for the Graphex then you should read the servicing section for the size you have. On a scale of 1, very simple, to 10, extremely difficult, the Graphex is a 4.5 to 5.5. On a scale of 1 to 10 ability, 1-knows what a screwdriver is, 10- capable of servicing space craft, 3 able to handle small common mechanical items should be able to handle the Clean and Lube IF you can read and follow instructions.
All you need to go from 200 to 400 is elbow grease.
High speed is nothing more than a booster spring that is twice as strong as the basic main lever spring that has to be compressed to give the higher speed. These springs can become stuck or the coils slightly corroded together causing extra force to be applied to the speed selector ring the first few times it is operated after a long sit. Figure 11 item 4; figure 17 item 12.
The service instructions are written for a complete tear down to bare case and reassembly. The shutter blade and aperture assemblies normally do not require removal/disassembly.
Use the site private message feature to contact me if you would like me to service your shutter or camera(s). _________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
|
bartbob
Joined: 30 Oct 2010 Posts: 102
|
Posted: Wed Jul 20, 2011 12:22 pm Post subject: |
|
|
I've been told that naptha isn't good for shutters with some non-metal parts in them as the lighter fluid may soften/degrade them. Are there any such parts in that shutter? Such as insulators in the flash sync parts? |
|
Back to top |
|
|
Henry
Joined: 09 May 2001 Posts: 1639 Location: Allentown, Pennsylvania
|
Posted: Wed Jul 20, 2011 1:55 pm Post subject: |
|
|
Some shutters have plastic diaphragm leaves, I'm told, but AFAIK our Graphex shutters don't have plastic. The only "plastic" I've found in mine are the little insulators in the synch contacts, and naptha has not been a problem for me. YRMV! |
|
Back to top |
|
|
bartbob
Joined: 30 Oct 2010 Posts: 102
|
Posted: Wed Jul 20, 2011 7:06 pm Post subject: |
|
|
Henry wrote: | .... but AFAIK our Graphex shutters don't have plastic. | Henry, would this apply to a Wollensak Full Synchromatic shutter used with the Graflex 90mm f/6.8 Optar lens? The one I got started out somewhat erratic and slow in all speeds (B,T, 1/2 to 1/400th). After some use at all speeds, it's now settled to a smaller spread in repeatability but still about 50% slow at all settings. 1/400th setting fires at 1/160th, 1/200th fires at 1/90th and 1/100th at 1/50th......
Last edited by bartbob on Wed Jul 20, 2011 7:09 pm; edited 1 time in total |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Wed Jul 20, 2011 7:09 pm Post subject: |
|
|
Ilex shutters have hard rubber shutter blades.
The flash sync insulators may seem OK but when you have to remove them they may disintegrate on reassembly. _________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
|
Henry
Joined: 09 May 2001 Posts: 1639 Location: Allentown, Pennsylvania
|
Posted: Thu Jul 21, 2011 1:13 am Post subject: |
|
|
When I said, a few posts above, that "I myself would not use any lubricant on the shutter mechanism," I lied (failing memory, for shame). Mix fine powdered graphite (sold as lock lubricant, in a small plastic tube, at the hardware store) into Ronsonol in a suitable container, such as a fine needle applicator, and squirt this mixture into the shutter as described above. Keep shaking the container as you work, as the graphite falls out of suspension rather quickly. When the naptha evaporates, you will have a very fine coating of graphite on the moving parts of the shutter mechanism. This may be the answer to stiff shifting into the 1/400 sec. speed.
What I've described is controversial, and there are those whose opinions I respect who would never advocate or employ it, on grounds of small particles coating inner surfaces of the lenses, etc. But I've never had a problem with it. |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Thu Jul 21, 2011 1:22 am Post subject: |
|
|
I dip a round tooth pick in TriFlow then wipe the inside of the gears or the shaft that the manual lists to oil. The fine sheen that results is all that is needed. I put a similar trace of white lithium grease on gear teeth.
Too much lubricant will be as bad or worse than dried lubricant.
I do put the extra fine graphite on shutter/aperture blades pivot points.
Henry,
What proportion do you mix the graphite to Ronsonol? _________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
|
DennisT
Joined: 17 Jul 2011 Posts: 8 Location: E WA state
|
Posted: Thu Jul 21, 2011 5:04 am Post subject: good |
|
|
I'm pleased with this thread. I'm learning a lot, which I need. Keep it up.
Dennis _________________ Dennis |
|
Back to top |
|
|
Henry
Joined: 09 May 2001 Posts: 1639 Location: Allentown, Pennsylvania
|
Posted: Thu Jul 21, 2011 4:58 pm Post subject: |
|
|
45PSS wrote: | I dip a round tooth pick in TriFlow then wipe the inside of the gears or the shaft that the manual lists to oil. The fine sheen that results is all that is needed. I put a similar trace of white lithium grease on gear teeth.
Too much lubricant will be as bad or worse than dried lubricant.
I do put the extra fine graphite on shutter/aperture blades pivot points.
Henry,
What proportion do you mix the graphite to Ronsonol? |
Um, ah, eh (he shrivels from embarrassment)---well, I'd have to call it "exact guesswork." Couple of squirts of the graphite (and I've found that not much comes out of the tube per squirt, but that depends somewhat on the size of the exit hole that I've punched in the tip with a sewing needle; please don't ask what size needle :-} ) Then add the Ronsonol direct from the container into the applicator bottle, which holds 1/2 fl. oz. and IIRC I only put in up to about 1/3 full, so say 1/6 fl. oz. As you said above, too much is worse than too little when it comes to lubricants, so I try to be sparing with the graphite quantity. |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Thu Jul 21, 2011 7:05 pm Post subject: |
|
|
If after the carrier fluid dries out and 25 to 30 shutter fires you notice specs on the inside of the glass you used too much graphite. _________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
|
Henry
Joined: 09 May 2001 Posts: 1639 Location: Allentown, Pennsylvania
|
Posted: Thu Jul 21, 2011 7:49 pm Post subject: |
|
|
When I photographed "tapping a heat" (i.e., releasing molten iron from the blast furnace) at Bethlehem Steel, there was a lot of flake graphite floating around in the cast house, and I was concerned for my camera gear (I was shooting 35mm Kodachrome64 in a Minolta SRT-101 for this assignment). But I didn't notice any effects. I probably should have been more concerned about what I was breathing! |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Thu Jul 21, 2011 8:08 pm Post subject: |
|
|
I was looking at my Super Speed's lens one day a few months after a complete CLA and there were specs on the inside of the glass, extra fine powdered graphite that I had applied to the aperture and shutter blades.
It has only happened once though. _________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
|
|